Click on a thumbnail/image to see more customer pictures.
Please be sure to measure your own snowblower slot sizes. Do not use this chart for ordering purposes. The number can be transposed very easily with a chart this large.
We would appreciate any and all information (in your own words), about your snowblower. Not just about the skids, but everything you would like to share. We have a lot of people coming to review different snowblowers, so any information you would like to share, would be appreciated.
Remember to always keep your snowblower off of the concrete when not in use. This helps to prevent rust. A 2×4 works great.
| Make/Model | Image/Links | Notes: | ARMORskids Control #: |
| *NEW CUT SERIES SKIDS* |  |
For Hydraulically Driven Utility Tractors Blowers such as: Bobcat, Meteor, Deere, New Holland, Kioti, Toro, Kubota, Woodmax and more. | CUT-SERIES |
| Agway 24″ 8HP | 24″ 8hp | ASE2475-A | |
| Ariens 30 |  |
Ariens 30″ Set at the manual’s suggested 7/8″ height for gravel. Spacers are needed. | ASE0310-B |
| Ariens 524 | ASE0310-B | ||
| Ariens 1028 | ASE0310-B | ||
| Ariens 1968 | 24″ | ASE0310-B | |
| Ariens 11528 | ASE0310-B | ||
| Ariens 920013 |  |
Spacers required due to scraper bar bolt near back. Alternatively some people have used longer bolts and a nut between auger housing and skid shoe. See picture. | ASE0310-B |
| Ariens 920014 | Deluxe ST24LE | ASE0310-B | |
| Ariens 920021 |  |
ASE0310-B | |
| Ariens 921020 | This uses the same skids as 921022 and 921030. | ASE0310-B | |
| Ariens 920022 | ASE0310-B | ||
| Ariens 921013 | Deluxe ST30LE | ASE0310-B | |
| Ariens 921017 |  |
24″ | ASE0310-B |
| Ariens 921022 | ASE0310-B | ||
| Ariens 921030 | ASE0310-B | ||
| Ariens 921038 | ASE0310-B | ||
| Ariens 921045 | ASE0310-B | ||
| Ariens 921046 | ASE0310-B | ||
| Ariens 921047 | ASE0310-B | ||
| Ariens 921049 | ASE0310-B | ||
| Ariens Deluxe 28 |  |
Note that spacers per side are required. | ASE0310 |
| Ariens Deluxe 921024 |  |
ASE0310-B | |
| Ariens 28 SHO | Note that spacers per side are required. | ASE0310-B | |
| Ariens 921030 |  |
ASE0310-B | |
| Ariens 921031 | ASE0310-B | ||
| Ariens 921032 |  |
||
| Ariens 921037 | ASE0310-B | ||
| Ariens 924028 | ASE0275-A | ||
| Ariens 920024 | ASE0310-B | ||
| Ariens 921048 | ASE0310-B | ||
| Ariens 921052 | ASE0310-B | ||
| Ariens ST824 924050 |  |
ASE0310-B | |
| Ariens Model 926053 | Ariens Model 926053 (HydroPro 28 - 2015) No spacers needed | PRO-0310-B | |
| Ariens 926500 |  |
||
| Ariens 926501-ST13336DLE | ASE3575-A | ||
| Ariens 932036 | ASE0310-B | ||
| Ariens 9526 DLEPRO | DLEPRO | ASE0310-B | |
| Ariens Platinum 24 | ASE0310-B | ||
| Ariens Platinum 30 |  |
ASE0310-b | |
| Ariens Pro 28″ | ASE0310-B | ||
| Ariens Pro 36″ |  |
ASE0310-B | |
| Ariens Rapid Trak Pro |  |
Pro-XT-3.0″ | |
| Ariens ST1032 | ASE3575-A | ||
| Ariens ST28LE | ASE0310-B | ||
| Ariens ST 524 | Spacers recommended due to rolled front edge. | ASE0310-B | |
| Ariens ST 928 |  |
Ariens ST 928 with Spacers | PRO3575-A |
| Ariens deluxe 24/2011 | 24″ | ASE0310-B | |
| Ariens snow tek/920402 | ASE0310-B | ||
| Ariens Sno-Tek 24E #920402 | ASE2505-B | ||
| Ariens Snow-Tek24E | ASE0310-B | ||
|
|
 |
Cut 24 skids for width 3.5″/7″ | CUT 24″ |
| Brute 1150 | ASE2505-A | ||
| Case Snow-Caster k84 (snowblower attachement) | Snowblower attachment | ASE3575-A | |
|
|
 |
ASE0275 | |
| Craftsman 247.88190 |  |
ASE3575-B | |
| Craftsman 247.883700 | 26′ Snow Thrower Model No. 247.883700 | ASE0275 | |
| Craftsman 247.883700 | ASE0275 | ||
| Craftsman 247.883961 |  |
Craftsman 247.883961 30″ | |
| Craftsman 247.88455.1 | 5.5hp 24″ | ASe0275 | |
| Craftsman 247.886640 | ASE0275 | ||
| Craftsman 247.887791 | 22″ | ASE0275 | |
| Craftsman 247.88830 |  |
ASE3575-B | |
| Craftsman 247.88955 |  |
||
| Craftsman 247.88970 | ASE0275 | ||
| Craftsman 247.88890 | ASE3575-B | ||
| Craftsman 247.88999 |  |
||
| Craftsman 247.881731 | ASE0275-A | ||
| Craftsman 24837 Craftsman 486.248371 |  |
The snow blower is a Sears Craftsman 42 inch, Two-Stage Snow Thrower for mounting on lawn tractors, Model number 24837 or 486.248371 | ASE2505-B |
| Craftsman 30″ | Craftsman 30″ 357 cc Model 88396 Electric Chute Two-Stage Snow Blower. | ASE3575-B | |
| Craftsman 486.24839 | ASE2475-B | ||
| Craftsman 536.881110 | ASC2475-A | ||
| Craftsman 536.811650 |  |
6.5hp, 24” (w/ a 2” skid bolt pattern) Model # 536.811650 and 536.881110 |
ASE2475-A |
| Craftsman 536.881851 |  |
8hp 27″ | ASE2475-A |
| Craftsman 536.881851 | ASE2475-A | ||
| Craftsman-536-887990 |  |
ASE2475-A | |
| Craftsman 536.887992 |  |
29 inch, 9 horsepower | ASE2475-A |
| Craftsman 536.887993 |  |
ASE2475-A | |
| Craftsman 536.887994 |  |
ASE2475-A | |
| Craftsman 536.887996 | ASE2475-A | ||
| Craftsman 88105 |  |
1/2″ Spacing 10.5 HP OHV/30 | ASE1545-A |
| Craftsman 88173 |  |
24″ 208cc | ASE0275-A |
| Craftsman 88690 | 28″ | ASE0310-B | |
| Craftsman 88957 | 24″ 179cc | ASE0275 | |
| Craftsman 889702 | ASE3575-B | ||
| Craftsman 944.520661 | ASE2505-A | ||
| Craftsman C950-52915-0 |  |
Craftsman C950-52915-0 | ASE-2475- |
| Cub Cadet 19A40024100 |  |
3X 42″ snow blower attachment | Pro-XT 3575-B |
| Cub Cadet 3X26 HD |  |
3 Stage Power. There are notes regarding this particular model. Please click on the image to the left to go to that page. | Pro-3575-B |
| Cub Cadet 3X28 |  |
357CC Snow Blower | Pro-XT-1545-B |
| Cub Cadet 3X-3 |  |
The new Cub Cadet 3 stage machines have mounting bolts higher than older models. We’ve developed an extra tall version of our Pro Series in three frequently requested sizes. The XT size is bases off our Pro Series 1/2″ thick bottom runner, and is 5 inches tall to give plenty of adjustment for those machines that have these issues with the regular series Armorskids®. –Bob |
Pro-XT-1545-A |
|
|
 |
The new Cub Cadet 3 stage machines have mounting bolts higher than older models. We’ve developed an extra tall version of our Pro Series in three frequently requested sizes. The XT size is bases off our Pro Series 1/2″ thick bottom runner, and is 5 inches tall to give plenty of adjustment for those machines that have these issues with the regular series Armorskids®. –Bob |
Pro-XT-3575-B |
| Cub Cadet 3×42 |  |
Attached to a XT2 lawn tractor… | PRO-XT3575-B |
| Cub Cadet 31AM59SS596 |  |
Cub Cadet 31AM59SS596 | |
| Cub Cadet 450 |  |
2072 Super Garden Tractor | ASE9275-B |
| Cub Cadet 524 WE |  |
2 Stage Power | Pro-XT-1545-A |
| Cub Cadet 524 SWE |  |
Pro-XT-3575-B | |
| Cub Cadet 526 SWE |  |
Pro-XT-3575-B | |
| Cub Cadet 528 |  |
Pro-XT-1545-B | |
| Cub Cadet 628-SWE | Pro-XT-1545-B | ||
| Cub Cadet 724E | ASE0275 | ||
| Cub Cadet 826t | ASE0310-B | ||
| Cub Cadet 945 SWE | Has 9″ bolts from first bolt to third bolt. | ASE9575-C | |
|
|
 |
Battery Powered EGO Brand 2400 | ASE0310-B |
| Honda HS80 | I have limited information on this machine. I think this has 2 3/8″ bolt spacing. | ASE2425-C | |
| Honda HS55 |  |
On the HS55 the skids are mounted on struts behind the housing. The new skids are way to large to fit in the original position. So I removed the old struts and skids and mounted the new skids to the main blower housing. I only had to drill one new hole for each skid, the second bolt was already there and available. Installation was quite quick. | ASE2425-C |
| Honda HS 724 |  |
Shown with the new Pro-Hond-2425-A skids. Note the new design gives a large clearance area for the back scraper bar bolt. However a couple people have reported needing a little more clearance for the scraper bar bolt. These people all had their skids adjusted all the way up to put their scraper bar down quite close to the ground for smooth new concrete. They report that the bolt still blocked them from doing so. So note that if additional clearance is needed, a moment or two with a grinder would take care of this. | Pro-HOND-2425-A |
| Honda HS828 |  |
Verify that you have mounting holes on the side of the auger housing. Some machines came with them, others did not. These holes are required to mount skids on side of auger housing. Spacers are required due to scraper bar bolt near back. Alternatively some people have used longer bolts and a nut between auger housing and skid shoe. Click on picture for more photos. | ASE2425-C |
| HONDA 928’s | NOTES > |
We don’t yet have pictures of the new skid on this machine. The pictures show the old recommended skid. See the pics on the 724 above. I recommend our new PRO-HON-2425-C. Thank you. Note the new design gives a large clearance area for the back scraper bar bolt. However a couple people have reported needing a little more clearance for the scraper bar bolt. These people all had their skids adjusted all the way up to put their scraper bar down quite close to the ground for smooth new concrete. They report that the bolt still blocked them from doing so. So note that if additional clearance is needed, a moment or two with a grinder would take care of this. |
Pro-Hond-2425-c |
| Honda HS928 |  |
Verify that you have mounting holes on the side of the auger housing. Some machines came with them, others did not. These holes are required to mount skids on side of auger housing. Original skids that sit behind the housing may be retained. Spacers are required due to scraper bar bolt near back. Alternatively some people have used longer bolts with a nut between auger housing and skid shoe. I do not have pictures of the 928 yet. See photos of 828 which is similar. | PRO-HON-2425-C |
| Honda HS928K1TAS |  |
PRO-HON-2425-C | |
| Honda HSS928 |  |
Todd used 3 spacers on his Honda HSS928. This machine takes the PRO-HON-2425-C skid. He’s using them on gravel and grass so he has them raised up to the max in this photo. | PRO-HON-2425-C |
| Honda HSS928AWD |  |
PRO-HON-2425-A | |
| Honda HS1132 TA | There was a little confusion at first because the Honda 1132 housing came two different ways, one with pre-drilled holes and one without. But Bob sorted it all out. I am posting here just to add to your recognition of Bob’s honest and good service. | ||
| Honda HS1332 |  |
Spacers required. Some people have used longer bolts and a nut or washers between auger housing and skid shoe. Click on picture for more photos. | PRO-HON-2425-C |
| Husqvarna 531-30 71-69 |  |
Pro-XT-250-B pictured. Shows wide range of adjustment available for the perfect setup for your own unique situation. | Pro2505-B |
| Husqvarna 1130sbexp | ASE1545-A | ||
| Husqvarna 11524E |  |
||
| Husqvarna 1252HV | ASE2505-A | ||
| Husqvarna 12527HVX |  |
Pro2505-A | |
| Husqvarna 1830EXLT | ASE2505-A | ||
| Husqvarna 1830HV | ASE2505-A | ||
| Husqvarna 5524ste | ASE2505-A | ||
| Husqvarna ST224 |  |
2.5″ slot spacing | ASE2505-A |
| Husqvarna ST227P |  |
ASE2505-A | |
| Husqvarna ST230E |  |
ASE2505-A | |
| Husqvarna ST230 P |  |
No spacers needed. | |
| Husqvarna ST324P | (2.5 inch slot spacing). | ASE2505-A | |
| Husqvarna ST330P |  |
Used on asphalt driveway and washed stone/gravel parking lot. Needs a longer bolt (by about ¼ inch) – (4 total) also, some spacers are needed, to mount the skid shoe to a flush surface. | ASE2505-A |
| Jacobsen/Ford LGT 165 |  |
41″ single stage | |
| John Deere 44 |  |
Note: picture is of the Pro series,Mounted on a 44″ tractor-mounted snowblower with a John Deere tractor. I recommend the Pro1545XT-B, it’s same skid design, with more height. The pro series is 3.5″ to top edge, where the Pro-XT series is 5″ to top of skid. | Pro1545XT-B |
| John Deere #46 | Does NOT fit due to massive flare on outside of blower housing. | N/A | |
| John Deere 47″ |  |
Mounted on a X534 Tractor. I recommend the Pro1545XT-B, it’s same skid design, with more height. The pro series is 3.5″ to top edge, where the Pro-XT series is 5″ to top of skid. | Pro1545XT-B |
| John Deere 47″ |  |
For Blower Attachment | ASE9575-C |
| John Deere 522 |  |
Customer DavidB says “This model has 2.5″ bolt spacing and your product fits perfectly. I realized after mounting and taking the photo that I need to swap sides to put the narrow end forward for use on our concrete driveway. Anyway… great product and great delivery!! Bring on the snow!” | ASE2505-A |
| John Deere 826 |  |
ASE2475-A | |
| John Deere 828D |  |
ASE0310-B | |
| John Deere 1028E |  |
ASE2505-A | |
| John Deere 1128de | ASE0310-B | ||
| John Deere 1130SE | ASE2505-A | ||
| John Deere 1330SE |  |
ASE2505-A | |
| John Deere 16342 |  |
John Deere 16342 - LA130 | ASE9545-C |
| John Deere 23045 | John Deere SKU 23045 | ASE1545-B | |
| John Deere TRS24 |  |
ASE2475-A | |
| John Deere TRS27 |  |
ASE2475-A | |
| John Deere TRS32 |  |
ASE2475-A | |
| John Deere x500 | ASE1545-B | ||
| John Deere 540X MT |  |
47″ | ASE9545-C |
| John Deere 42″ Blower | |||
| John Deere 59″ Blower |  |
4.75″ on center | C.U.T. 24 |
| John Deere TRX-24 | ASE2475-A | ||
| John Deere D170 | ASE9545-C | ||
| Jonsered ST 2376 EB |  |
30″ 2 ½ inch centers | ASE2505-A |
| Kioti CS-2410 |  |
The blower is a Kioti KS50 The factory skids (a $125 option, stock it just rides on the edge of the housing!!!) wore out in one season and were absurdly small for the size of the blower. | ASE1545-C |
| Kioti KS50 |  |
Kioti KS50-160FM | C.U.T. 24″ |
| Kioti KS54 |  |
Kioti KS54-180FM | C.U.T. 24″ |
| Kubota 2660 | Kubota BL2660 (60″). This 3-point mounted pto machine weighs about 450 lbs. It has the standard Kubota 2 1/8″ bolt spacing. I do not have a good picture of the skids mounted on a BL2660 yet. | C.U.T. 24″ Kubota | |
| Kubota B2782 |  |
Kubota B2782 (63″) | C.U.T. 24″ Kubota |
| Kubota 5450 / BX5450 |  |
I just got the skids, all I can is WOW!!!! Pictures don’t do them justice. I went ahead and put them on and fit perfect. | PRO2425-A OR CUT 24″ |
| Kubota B2781B |  |
CUT 24″ Series for Kubota, and mounted on a Kubota B2781B blowers. | C.U.T. 24″ |
| Kubota BL2664 3 Point |  |
Here are some photos installed. I had to put some 3/16″ spacers behind them so they could clear the wings. These are temporary since i would like to use 5×8 3/16″ plates (painted) for the final configuration. That will come later though. I’m anxious to try them out. They should help considerably. | CUT24KUB2.125 |
| Kubota BX2816 / 23S |  |
ASE9255-A | |
| Kubota GR2846A |  |
PRO-XT-2505-B | |
| Lambert HS2540 | ASE3575-A | ||
| Lawn Boy |  |
Lawn Boy #522R model 28230 | |
| Little Wonder Vacuum |  |
Little Wonder Leaf Vacuum | ASE0650-A |
| LS Snowblower |  |
Tractor-Mounted LS Brand Snowblower LW3174A-74 | C.U.T. 30″ 6.5 |
| Mahindra |  |
Mahindra Snowblower Skid 54″ | C.U.T. 24″ |
| Massey 2360 |  |
Massey 2360 Snowblower Attachment | C.U.T. 24″ |
| Mastercraft 10.5HP (MTD) | 10.5 hp | ASE0275 | |
| Meteor 51 |  |
C.U.T. Series 24″ | |
| MTD 190-032 | I recommend the 9000 series for this machine. | ASE9575-B | |
| MTD 190-823 | PRO-3575-B | ||
| MTD 300 Series |  |
||
| MTD 31AE640F161 | ASE0275 | ||
| MTD 31AS6FEF700 | ASE0275 | ||
| MTD 31A62BD700 |  |
ASE0275-A | |
| MTD 316611 | ASE0275 | ||
| MTD 317-611d118 | ASE0275 | ||
| MTD Yard Machines Series 500-600 | ASE0275 | ||
| MTD 524 | ASE0275 | ||
| mtde660g | ASE0275 | ||
| 26″ Yard Machine by MTD | 26″ | ASE0275 | |
| MTD 5/21 | ASE0275 | ||
| MTD 8/26 | ASE0275 | ||
| MTD/Troy Built 190-823-101 | ASE3575-B | ||
| Yard Machine 31AE6A4E129 | ASE3575-B | ||
| MTD Yard Machine 31A-E662H013 |  |
ASE0275-A | |
| MTD YardWorks 31AE6MKH515 |  |
10.5 HP 30″ | |
| MTD Yard Machine 31aj11d129 | ASE0310-B | ||
| MTD Yard Machines 31am63ef 700 | ASE0275 | ||
| MTD Yard Machines 31as6fee729 | ASE0275-B | ||
| Murray 27 inch 627809x5A | 27″ | ASE2505-A | |
| Nomar G2794010 | ASE2505-A | ||
| NOMAR27″/ 627104X8 | 27″ | ASE2505-A | |
| Poulan Pro PR242 |  |
ASE2505-A | |
| Poulan Pro PR624ES |  |
More notes on the page. Click the thumbnail | ASE1545-A |
| Poulan Pro XT11530ES | ASE1545-A | ||
| Power Smart DB765922 |  |
22″ 2 Stage Electric | |
| Quality Pro (mtd) | MTD | ASE0275 | |
| Sears 247.886510 | ASE0310-B | ||
| Sears 944.529201 | ASE1545-A | ||
| Simplicity 860 SE |  |
||
| Simplicity 870 | ASE2505-A | ||
| Simplicity 7/55 | ASE2505-A | ||
| Simplicity 1690169 | ASE2505-A | ||
| Simplicity 1694241 | ASE2505-A | ||
| Simplicity 1428L | ASE2505-A | ||
| Simplicity 1691900 860se | ASE2505-A | ||
| Simplicity 860se | ASE2505-A | ||
| Simplicity M1227e | Simplicity M1227e / 1696819 | ||
| Simplicity P1524E | ASE2505-A | ||
| Snapper L1226E |  |
He’s using the 2.5″ bolt pattern slots. | ASE505 |
| Snapper 1227 |  |
||
| Snapper 1030 |  |
ASE0310 | |
| Snapper 8246 |  |
ASE9310-A | |
| Snapper 9226 E |  |
ASE0310-B | |
| Snow Joe |  |
Snow Joe 2 Stage 100 Volt Snowblower | ASE0310-B |
| Toro 521 |  |
This Rocks! | |
| Toro 1132 Before 1991 |  |
The Toro 1132 Powershift Snowblower (up to 1991) used a 2.5″ bolt pattern, and can use the ASE2505-A the Pro-2505-A. | |
| Toro 1132 After 1991 | |
The Toro 1132 Powershift Snowblower (after 1992 and newer) takes the ASE0310-D or the PRO-0310-D | |
| Toro 38051 | Also fits Lawn Boy 522R | ||
| Toro 38052 | ASE2475-A | ||
| Toro 38614 | ASE0275 | ||
| Toro 726OE | ASE0310-B | ||
| Toro Powermax 724 OE |  |
The ASE0310 skids at 3.00 inch spacings work great on my Toro Powermax 724 OE snowblower that I bought in 2017… | ASE0310 |
| Toro Powermax 728LXE | Has skids set back on auger housing. See notes and pictures. May require adjustment of scraper bar. Feedback and pictures required if you order this, as it’s still in development. | ASE0310-D | |
| Toro 824 |  |
ASE0310-D | |
| Toro 826 LE |  |
ASE0310-D | |
| Toro 826OXE |  |
ASE0310-D | |
| Toro Powermax 828LXE |  |
Has skids set back on auger housing. See notes and pictures. May require adjustment of scraper bar. Feedback and pictures required if you order this, as it’s still in development. | ASE0310-D |
| Toro 926 OXE |  |
I used approximately 2” washers for spacers between the skids and the snow blower side plate. One at each bolt. I adjusted the skid height so there would be approximately an inch bottom of skid to bottom of blower. I may have to make more adjustments when I actually do some blowing. | ASE0310-D |
| Toro 928 OHXE |  |
See picture of ase0310-d mounted. You probably want to use the spacer kit due to a flange at the front of the auger housing. | ase0310-D |
| Toro Lawn-Boy #522R |  |
||
| Toro Powermax 1028OHXE |  |
Has skids set back on auger housing. See notes and pictures. May require adjustment of scraper bar. Feedback and pictures required if you order this, as it’s still in development. | ASE0310-D |
| Toro 1128 OXE | ASE0310-D | ||
| Toro 38051 | Also fits Lawn Boy 522R | ||
| Toro 38052 | ASE2475-A | ||
| Toro 38614 | ASE0275 | ||
| Toro SnowMaster 724QXE |  |
Toro SnowMaster 724QXE model 36001 Shim kit (spacers) mandatory to clear the stampings. |
ASE2505-A |
| Toro SnowMaster 724 ZXR | Shim kit (spacers) mandatory to clear the stampings. | PRO2505-A | |
| Toro snowmaster-824-QXE-36003 |  |
Toro snowmaster-824-QXE-36003 | ASE2505-A |
| Troy-Bilt Arctic Storm XP 34” |  |
Model Number: 31AH8ER6766 | Pro-XT-3575 |
| Troy-Bilt Flex 26 |  |
Troy-Bilt Flex 26″ | ASE0275 |
| Troy-Bilt Polar Blast 13045 |  |
45″ Wide | ASE9575-C |
| Troy-Bilt Storm 2410 |  |
ASE0275-A | |
| Troy-Bilt Storm 2620 |  |
26″ | ASE0275-A |
| Troy-Bilt Storm 2625 |  |
||
| Troy-Bilt Storm 2840 |  |
ASE3575-B | |
| Troy-Bilt Storm 3090 XP |
Home Use: ASE3575-B Commercial Use: Pro3575-B. |
||
| Troy-Bilt 45 |  |
ASE9575-C | |
| Troy-Bilt Storm 5524 |  |
ASE0310-B | |
| Troy-Bilt 31AS62N2711 | ASE0275-A | ||
| Troy-Bilt/Lowes 31AS62N2711 | Lowes | ASE0275-A | |
| Troy-Bilt 31BM63P3711 | 26″ | ASE0275-A | |
| Troy-Bilt 33 | ASE1545-B | ||
| Troy-Bilt Storm 5524 31AS6BN2711 | ASE0275-A | ||
| Troy-Bilt Storm 3090xp | ase3575b or pro3575b. | ASE3575-B | |
| Troy-Bilt 31AS6BN2711 | 24″ 179cc | ASE0275-A | |
| Troy-Bilt Storm 9528 |  |
28″ Clearing | ASE0275-A |
| Troy-Bilt Vortex Tracker 2890 | 5.75″ bolt pattern | ASE3575-B | |
| Versatile V-48 | ASE3575-A | ||
| Bob’s Snowblower |  |
||
| White 800ST | ASE0275-A | ||
| Woodmax |  |
C.U.T. 30″ long and 8.5 slot spacing Un-Painted | C.U.T.30 8.5″ |
| Yardworks/Yardmachines | SEE MTD | ASE0275-A |
Click on a thumbnail/image to see more customer pictures.
Please be sure to measure your own snowblower slot sizes. Do not use this chart for ordering purposes. Number can be transposed very easily with a chart this large.
